* Estimated delivery times start from the date of shipment, excluding processing time.
* Actual delivery times may vary due to holidays, weather conditions, or customs delays.
Paket je prišel rahlo poškodovan, vendar merilni inštrument je brezhiben in deluje odlično. Napetost kaže zelo natančno, napetost, pa bo potrebno naravnati na pravi rezultat. Priporočam nakup, zelo kvalitetna izdelava.
Paket je prišel rahlo poškodovan, vendar merilni inštrument je brezhiben in deluje odlično. Napetost kaže zelo natančno, napetost, pa bo potrebno naravnati na pravi rezultat. Priporočam nakup, zelo kvalitetna izdelava.
Paket je prišel rahlo poškodovan, vendar merilni inštrument je brezhiben in deluje odlično. Napetost kaže zelo natančno, napetost, pa bo potrebno naravnati na pravi rezultat. Priporočam nakup, zelo kvalitetna izdelava.
KWS DC200 10A arrived undamaged. The instruction manual shows how to connect with the power supply from the same source
what and load. There is a warning there: Don't connetct thin black wire. On the case they show to connect a thin black wire to a thick black wire. So against my own warning. Such connection as on the sticker on the back of the meter in similar designs of voltmeters -ammeters causes their damage. The topic is known and described on the Internet. KEWEISI manufacturer which is correct? I didn't risk damaging it. I connected according to the attached instructions, and not according to the diagram from the housing. It works. Maybe someone was checking it. Write in the comments. Maybe Banggood will find out with the manufacturer where such a discrepancy in the schemes is and give it on the item's page. Another note. The specification gives a supply voltage from 8V to 120V. My copy starts the display only from 14.40V, regardless of the power supply from one or two sources. Below 14.4V, the display (photo) goes out. How do you have in your copies? The measurement error is small (photo), so it's probably not a matter of calibration.
KWS DC200 10A arrived undamaged. The instruction manual shows how to connect with the power supply from the same source
what and load. There is a warning there: Don't connetct thin black wire. On the case they show to connect a thin black wire to a thick black wire. So against my own warning. Such connection as on the sticker on the back of the meter in similar designs of voltmeters -ammeters causes their damage. The topic is known and described on the Internet. KEWEISI manufacturer which is correct? I didn't risk damaging it. I connected according to the attached instructions, and not according to the diagram from the housing. It works. Maybe someone was checking it. Write in the comments. Maybe Banggood will find out with the manufacturer where such a discrepancy in the schemes is and give it on the item's page. Another note. The specification gives a supply voltage from 8V to 120V. My copy starts the display only from 14.40V, regardless of the power supply from one or two sources. Below 14.4V, the display (photo) goes out. How do you have in your copies? The measurement error is small (photo), so it's probably not a matter of calibration.
KWS DC200 10A arrived undamaged. The instruction manual shows how to connect with the power supply from the same source
what and load. There is a warning there: Don't connetct thin black wire. On the case they show to connect a thin black wire to a thick black wire. So against my own warning. Such connection as on the sticker on the back of the meter in similar designs of voltmeters -ammeters causes their damage. The topic is known and described on the Internet. KEWEISI manufacturer which is correct? I didn't risk damaging it. I connected according to the attached instructions, and not according to the diagram from the housing. It works. Maybe someone was checking it. Write in the comments. Maybe Banggood will find out with the manufacturer where such a discrepancy in the schemes is and give it on the item's page. Another note. The specification gives a supply voltage from 8V to 120V. My copy starts the display only from 14.40V, regardless of the power supply from one or two sources. Below 14.4V, the display (photo) goes out. How do you have in your copies? The measurement error is small (photo), so it's probably not a matter of calibration.
Tips:For questions about your order, place of delivery, product discount, taxation, delivery time, warranty, shipping, payment, exchange rate, and other questions unrelated to the product, please contact customer service.
showing 1-24 of 24|
Show Original
A part of the QA has been auto-translated.
0
Q:
What is the 2 pin connector on the bottom edge? Right below the "KWS-DC200"?
What is the 2 pin connector on the bottom edge? Right below the "KWS-DC200"?
vou comprar quando receber meu salário entendeu agora eu tô sem dinheiro porque eu tô gastando muito aqui em casa mas eu deixei na lista para quando eu puder eu comprar muito obrigado
I will buy when I receive my salary, do you understand? Now I don't have money because I'm spending a lot here at home, but I put it on the list so that when I can, I will buy. Thank you very much.
Answered by JacksonPintoMaia on 31/03/2024Helpful (0)
Does it come pre calibrated to fit the chosen shunt (100A in my case)? What is the minimum load measured? Ex: 100A=75mV across the shunt. Will a load of 1W, less than 0.075mV across shunt be measured? As of now I don't get a load reading at all *sigh*, just voltage and temp.
Does it come pre calibrated to fit the chosen shunt (100A in my case)? What is the minimum load measured? Ex: 100A=75mV across the shunt. Will a load of 1W, less than 0.075mV across shunt be measured? As of now I don't get a load reading at all *sigh*, just voltage and temp.
Will this device count both up and down? If connected to a battery? will it count Ah and - or just count upwards regardelss if the battery is charging or discarging?
Will this device count both up and down? If connected to a battery? will it count Ah and - or just count upwards regardelss if the battery is charging or discarging?
Hi, I use this device on input of solar inverter. I dont test on batery count. Best tip, I tested next week.
Hi, I use this device on input of solar inverter. I dont test on batery count. Best tip, I tested next week.
Answered by Doctor on 02/02/2023Helpful (0)
0
Q:
Can I use this on my mobility scooter with 2 x 80 amp Lithium batteries ? I like to see the state of my batteries to controll my eventuell distance I have left . Thank you
Can I use this on my mobility scooter with 2 x 80 amp Lithium batteries ? I like to see the state of my batteries to controll my eventuell distance I have left . Thank you
Intheory, yes. The precise wiring you'll need to achieve this I can't speculate on without knowing more of your scooter. Worst case is you'd need one per battery.
Intheory, yes. The precise wiring you'll need to achieve this I can't speculate on without knowing more of your scooter. Worst case is you'd need one per battery.
Answered by BG161213372 on 13/04/2023Helpful (0)
0
Q:
I want to store the readings obtained by HX711 of a continuously variable weight. Which tool (with USB interface and Win processing software) do you recommend? Thank you
I want to store the readings obtained by HX711 of a continuously variable weight. Which tool (with USB interface and Win processing software) do you recommend? Thank you
Hi, does it have a standby mode and what is the power consumption (standby/work) on a 12V source. Does ist count ingoing and outgoing current (+/-) and allow monitoring battery energy ? Thanks in advance. Greetings, Laurent
Hi, does it have a standby mode and what is the power consumption (standby/work) on a 12V source. Does ist count ingoing and outgoing current (+/-) and allow monitoring battery energy ? Thanks in advance. Greetings, Laurent