* Estimated delivery times start from the date of shipment, excluding processing time.
* Actual delivery times may vary due to holidays, weather conditions, or customs delays.
Tips:For questions about your order, place of delivery, product discount, taxation, delivery time, warranty, shipping, payment, exchange rate, and other questions unrelated to the product, please contact customer service.
showing 1-11 of 11|
Show Original
A part of the QA has been auto-translated.
0
Q:
The transformer has 4 wires coming out of it, but they connect to 3 holes. Which wires correspond to which hole?
The transformer has 4 wires coming out of it, but they connect to 3 holes. Which wires correspond to which hole?
se encuentra en la parte de abajo, incluso en la pcb te India el (+) positivo y (-) negativo, le puedes colocar un voltaje min. De 3v y máx. De 5v si pasas el voltaje indicado lo vas a quemar y en caso contrario si es menos no va funcionar.
is located at the bottom, even in the pcb te India the positive (+) and negative (-) you can put a voltage min. 3v and max. Of 5v if you pass the indicated voltage you will burn it and otherwise if it is less it will not work.
Answered by RAULOROZCO on 06/08/2022Helpful (0)
0
Q:
Lots of wires coming from one of the components. These wires are tangled. How do you wire them to the board?
Lots of wires coming from one of the components. These wires are tangled. How do you wire them to the board?
If you look the website description and drawing, there is a clear guide how to wire the transformers on the pcb. Hint is the positioning of the windings. If you can follow that it should work. ( 2 - thin windings start and end. 2 - thick windings start and end. Thin winding end and thick winding start should be the center tap or joined together.
If you look the website description and drawing, there is a clear guide how to wire the transformers on the pcb. Hint is the positioning of the windings. If you can follow that it should work. ( 2 - thin windings start and end. 2 - thick windings start and end. Thin winding end and thick winding start should be the center tap or joined together.
Answered by JeffdHal on 19/10/2021Helpful (0)
0
Q:
my lighter worked for the first few seconds and then didn't work at all unless I touch both the wires with each other even after that there was a tiny spark it is not working please help. and the transistor is heating too much. Please help
my lighter worked for the first few seconds and then didn't work at all unless I touch both the wires with each other even after that there was a tiny spark it is not working please help. and the transistor is heating too much. Please help
I have a problem with cargo. On tracking page it says cargo has not seen any action since 31/12. What is the problem. my tracking no is ALJPK8362000226YQ.
I have a problem with cargo. On tracking page it says cargo has not seen any action since 31/12. What is the problem. my tracking no is ALJPK8362000226YQ.
There is a time limit and it will appear some time later.
There is a time limit and it will appear some time later.
Answered by katherine on 28/04/2018Helpful (0)
0
Q:
The transformer arrived damaged...the wires were not tangled, had 4 wires instead of 3...didn't work because of that...and I am still waiting for an answer!
The transformer arrived damaged...the wires were not tangled, had 4 wires instead of 3...didn't work because of that...and I am still waiting for an answer!
THE INSTRUCTIONS SHOW A TRANSISTOR WITH THREE LEGS AND A HEAT SINK TAB. THE SUPPLIED TRANSISTOR DOESN'T HAVE THE HEAT SINK TAB AND THE CENTER LEG IS CLIPPED OFF. DO YOU HAVE UPDATED INSTRUCTIONS TO REFLECT THIS.
THE INSTRUCTIONS SHOW A TRANSISTOR WITH THREE LEGS AND A HEAT SINK TAB. THE SUPPLIED TRANSISTOR DOESN'T HAVE THE HEAT SINK TAB AND THE CENTER LEG IS CLIPPED OFF. DO YOU HAVE UPDATED INSTRUCTIONS TO REFLECT THIS.